Repairs to uPVC Windows

uPVC is a fantastic option for modern homes. They are durable, long-lasting and easy to maintain. They are not susceptible to get rotten or rusty like aluminum and timber.

Cleaning and lubricating regularly UPVC windows and doors is crucial. This will prevent unnecessary repair costs as well as improve energy efficiency.

1. Broken Glass

The damaged glass in your windows could cause serious damage to your home and may even be fatal. You should take the time to ensure that your windows are in good working order.

Single-pane windows are fairly simple to replace, and they typically fit into frames of the past easily. If windows with double panes are held together by internal beading, it is harder to remove and replace the panes that were previously in use. In this situation you'll need to locate some plastic spacers to assist the new pane to fit properly into the window frame.

Wearing eye protection and heavy gloves is essential for anyone who plans to remove the glass yourself. It is also a good idea to lay down a drop cloth prior to when you start working on the glass so that any shards will fall on the fabric instead of onto the floor where they could be trampled upon and cause further damage.

Once the glass is removed from the window, it's best to cover the gap with some clear packaging tape or duct tape to prevent drafts and water from entering the property until a professional can come out and fix the window. This will also provide an obstruction to prevent criminals from getting into your home. If the gap is particularly large, you might think about an alarm door that comes with an integrated window as it will provide the best of both worlds.

2. Sagging

uPVC windows and doors are an affordable energy-efficient, durable and long-lasting alternative to timber sash windows. However, over time, they are susceptible to a range of issues, including sliding. A window that isn't properly aligned can cause problems with light, draughts and even security. If you notice that your uPVC window is beginning to sag it is important to act swiftly to stop the issue from getting worse.

To Repair My Windows And Doors a window that is sagging, you can try repositioning the hinges. To accomplish this, you'll need to open the window to access the frame. After that, using an screwdriver, take off the hinges at the top and bottom and adjust them by turning them clockwise or counter-clockwise. Once you've repositioned the hinges, close the window and check for fit. If you are happy with the fit of the window, tighten the screws to secure them in the right position.

If you cannot reposition the hinges, you might need to replace the seal. Over time rubber seals can lose their elasticity and become dry, which causes them to loosen. It is essential to replace your seal as quickly as you can to keep your uPVC window watertight and draughtproof.

UPVC handles can also become loose. This is typically caused by screws that have become undone over time, but it could be caused by the handle mechanism wearing out. Fortunately, it's easy to repair a loose uPVC window handle yourself. You'll first need to close the window and perform an initial fitting. The corners of the sash must be aligned with the casing joint. If it doesn't, you can use a screwdriver to loosen the handle and then reverse the mechanism back into position.

3. Water Leaks

It is essential to take action if you awake each day to find mouldy walls and floors that are wet. Windows that leak water do can not only cause destruction of your home's structure but also undermine your efforts to regulate the temperature in your home. The most frequent reason for leaking uPVC windows is that the sealant around the frame is either damaged or missing.

This is a fairly simple fix and should be undertaken by any competent DIYer. Depending on how severe the issue is, old caulking may need to be removed. It is crucial to remember that when it comes to uPVC window repairs, you should not be tempted to 'over-caulk' as this will only make the area more difficult to clean and decrease the efficiency of your energy usage.

It is essential to ensure that the drainage holes are clear of debris and that the sill pan is angled in a way that allows it to drain away from the window. In more serious cases you may need to think about replacing the window.

Mold spots and rotted sills are another sign of water leakage. This fungus thrives in damp conditions and can spread quickly throughout the house.

If the leakage occurs between the double-glazed glass, it is more likely the problem is with the seal rather than the frame. It is also possible to be fixed by an uPVC window specialist who will replace the glass seal and regain the full insulation properties of your windows.

4. Faulty Hinges

Hinges may be to blame for the reason that your uPVC window is difficult to open or if it opens with the breeze. Any competent DIYer can replace these in a matter of minutes.

Like any mechanical component hinges are prone to wear out over time. It's easy to change the hinges on a window however it is easier if someone helps you to hold the frame.

It is also important to verify that the uPVC hinges are opening and closed in the right direction. You can check this by looking for the arrow on each hinge, this indicates which way the window should be opened.

Faulty window hinges could be the result of incorrectly opening the window in a particular manner or Repair My Windows And Doors because of improper installation in the factory. Sending us photos through our website can often solve the issue. We are always happy to offer advice.

Regularly lubricating the hinges is essential. This can be done by applying an oil that is light in nature to the hinges, we recommend using a solvent-free lubricant such as 3-in-one Multi-Purpose Oil. Regular lubrication can allow the window to operate and close more smoothly. It also decreases the chance of windows sticking and prevent corrosion. It is recommended to do this at least once a year. WD40 or other solvent-based oils are not recommended as they could damage your uPVC windows.

5. Draughts

Draughts can be caused by several different causes. The hinges can also become unbalanced due to wear, causing gaps where the sash and frame meet. They can be fixed by giving them a good clean, but if they are beyond repair it could be necessary to get them realigned or replaced. In addition, the interlock could also become disaligned. This is located on the hinge side and may need to be cleaned. In some instances it might be necessary to replace the hinges.

The second most frequent cause of draughts is the window seals. These are susceptible to being worn out or damaged over time and let air escape through these gaps. This can be avoided by replacing them with high-quality weatherstripping. Another alternative is to replace the window with glass that is low-emissivity, this will help in regulating indoor temperatures and again will lessen the possibility of draughts.

The last way to reduce the amount of draughts is to use a Draught-excluder. These are typically fabric tubes filled with a filler, which can be placed over your window sill. They will help stop cold air from entering and keep your home warm and cozy!

The windows made of upvc can keep providing excellent insulation and security for your home with a little regular maintenance and repairs. It is important to remember that all windows eventually get worn out and it is cheaper to replace them than to repair them. If you are experiencing issues with your Upvc window you should consult an expert immediately.